Serviceline Industrial Sensors
Serviceline Explosion Protection
Gateway for PROFINET LB8122A.1.EL
- Communication via PROFINET
- Mounting in Zone 2, Class I/Div.2 or in the safe area
- Interface between the I/O modules and the PCS/PLC
- Non-volatile memory for configuration and parameter settings
- Permanently self-monitoring
- MRP and S2 redundancy
- HART communication via HART-IP
- Shared Device und Dynamic Reconfiguration
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Datasheet excerpt: Technical data of LB8122A.1.EL
| Supply | ||
|---|---|---|
| Connection | backplane bus | |
| Rated voltage | 12 V DC , only in connection with the power supplies LB9*** | |
| Nominal voltage | 12 V DC , | |
| Power dissipation | 4.53 W | |
| Power consumption | 4.53 W | |
| Fieldbus connection | ||
| Fieldbus type | PROFINET | |
| Ethernet Interface | ||
| Connection type | RJ-45 , via front connector | |
| Transfer rate | 10BASE-T, 100BASE-TX 100 MBit/s | |
| Station connection | directly to PCS or PLC or via hubs or switches | |
| Cable type | SFTP in accordance with ISO/IEC 11801 for Cat 5e or better | |
| Bus length | max. 100 m per link | |
| Addressing | DHCP, via controller (DCP) or fixed IP address | |
| Ethernet address | IP V4 address (preset: DHCP on, changeable via display) | |
| Supported I/O modules | LB1x01*…LB1x03*, LB1x08*, LB1x09*, LB2x01*…LB2x17*, LB3x01*…LB3x06*, LB4x01*, LB4x02*, LB4x04*…LB4x06*, LB5x01*, LB5x02*, LB5x04*…LB5x06*, LB6x01*, LB6x05*, LB6x06*, LB6x08*, LB6x10*…LB6x17*, LB7x04* | |
| PROFINET conformance class | CC B | |
| Internal bus | ||
| Connection | backplane bus | |
| Galvanic isolation | ||
| Ethernet/other circuits | basic insulation according to IEC/EN 61010-1, rated insulation voltage 35 Veff or 50 V DC | |
| RS 485 interface/other circuits | basic insulation according to IEC/EN 61010-1, rated insulation voltage 35 Veff or 50 V DC | |
| Insulation voltage | 1500 V AC acc. to IEEE 802.3u | |
| Electrical isolation | ||
| Power supply, internal bus/other circuits | basic insulation according to IEC/EN 61010-1, rated insulation voltage 30 V DC | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 | |
| Conformity | ||
| Degree of protection | IEC 60529 | |
| Fieldbus standard | IEEE 802.3 | |
| Environmental test | EN 60068-2-14 | |
| Shock resistance | EN 60068-2-27 | |
| Vibration resistance | EN 60068-2-6 | |
| Damaging gas | EN 60068-2-42 | |
| Relative humidity | EN 60068-2-78 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Relative humidity | 95 % non-condensing | |
| Altitude | max. 2000 m | |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 | |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
|
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 | |
| Mechanical specifications | ||
| Degree of protection | IP20 (module) , mounted on backplane | |
| Connection | via backplane | |
| Mass | approx. 150 g | |
| Dimensions | 32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch) | |
| Data for application in connection with hazardous areas | ||
| Certificate | DEMKO 16 ATEX 1780 X | |
| Marking |  II 3 G Ex ec IIC T4 Gc |
|
| Directive conformity | ||
| Directive 2014/34/EU | EN IEC 60079-0:2018+AC:2020 EN 60079-7:2015+A1:2018 |
|
| International approvals | ||
| ATEX approval | DEMKO 16 ATEX 1780 X | |
| IECEx approval | IECEx UL 16.0141 X | |
| Approved for | Ex ec IIC T4 Gc | |
| General information | ||
| System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2, Zone 22 or Div. 2) the module must be installed in an appropriate enclosure. |
|
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210121 |
| ECLASS 12.0 | 27210121 |
| ECLASS 11.0 | 27210121 |
| ECLASS 10.0.1 | 27210121 |
| ECLASS 9.0 | 27210121 |
| ECLASS 8.0 | 27210121 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC001485 |
| ETIM 8.0 | EC001485 |
| ETIM 7.0 | EC001485 |
| ETIM 6.0 | EC001485 |
| ETIM 5.0 | EC001485 |
| UNSPSC 12.1 | 39121008 |
Details: LB8122A.1.EL
The PROFINET gateway is the interface between the I/O modules on the backplane and the control system.
HART communication is via PROFINET or HART-IP.
In addition to the input/output data of the I/O modules, the HART auxiliary variables can also be accessed in the process image.
Datasheet: LB8122A.1.EL
| Datasheet | File Type | File Size |
|---|---|---|
| Datasheet LB8122A.1.EL | 583 KB | |
| Datenblatt LB8122A.1.EL | 585 KB |
Documents: LB8122A.1.EL
CAD+CAE: LB8122A.1.EL
| CAD | File Type | File Size |
|---|---|---|
| CAD 3-D / CAD 3-D | STP | 1977 KB |
Approvals+Certificates: LB8122A.1.EL
| Certificates | File Type | File Size |
|---|---|---|
| Brasil TUV Rheinland Brazil | 1124 KB | |
| Canada, USA UL cULus | 646 KB | |
| China SITIIAS CCC Ex Certificate | 1085 KB | |
| Europe DEMKO ATEX | 176 KB | |
| South Africa MASC | 730 KB | |
| Worldwide UL IECEx Certificate of Conformity | LINK | --- |
| Declaration of Conformity | ||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | 1038 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | 2033 KB |
Software: LB8122A.1.EL
| Device Driver | File Type | File Size |
|---|---|---|
| CFC Device Driver Blocks for SIMATIC PCS 7 / CFC Device Driver Blocks for SIMATIC PCS 7 | ZIP | 15869 KB |
| GSDML file for LB/FB PROFINET Gateways LB/FB8x22 / GSDML-Datei für LB/FB PROFINET Gateways LB/FB8x22 | ZIP | 357 KB |
| Device type managers (DTM) | ||
| DTM / DTM | ZIP | 9478 KB |
| Firmware | ||
| Firmware / Firmware | ZIP | 139834 KB |
The new LB/FB PROFINET gateways from Pepperl+Fuchs open the door for IIoT 4.0 applications in process industries.
Pepperl+Fuchs SE
Lilienthalstraße 200
68307 Mannheim
Germany
info@de.pepperl-fuchs.com
+49 621 776-0
© 2024 All Rights Reserved.
Pepperl+Fuchs is a leading developer and manufacturer of electronic sensors and components for the global automation market. Continuous innovation, enduring quality, and steady growth have been the foundation of our success for more than 70 years. Pepperl+Fuchs employs 6,300 people worldwide and has manufacturing facilities in Germany, USA, Singapore, Hungary, Indonesia and Vietnam, most of them ISO 9001 certified.